Aem 30-5144 Analog Boost Fuel Pressure SAE Gauge Uživatelský manuál stáhnout pdf

AEM Performance Electronics

2205 126

Street Unit A, Hawthorne, CA. 90250

Phone: (310) 484-2322 Fax: (310) 484-0152

http://www.aemelectronics.com

Instruction Part Number: 10-5144 Rev 01

 2010 AEM Performance Electronics

Part Number 30-5144

Analog Style 15 PSI Fuel/Boost Pressure Gauge

NOTE: Faceplate Configuration Instructions Included on Separate Sheet

Figure 1. Wiring Schematic

AEM Oil/Fuel Pressure Gauge Parts

1 x 35-5144 Pressure Gauge Assembly

1 x 30-2131-15 PSIG Pressure Sensor

1 x 35-4302 Install Kit (6 Butt Connectors)

1 x 10-5144 Installation Instructions

1 x 35-3411 8-Pin Power Harness

1 x 35-3412 3-Pin Sensor Harness

1 x 35-8529S Silver Bezel

1 x 35-8550W Fuel Pressure Faceplate, White

1 x 35-8551B Boost Pressure Faceplate, Black

1 x 35-8551W Boost Pressure Faceplate, White

1 x Faceplate Configuration Instructions

1 x Paper Clip Needle Removal Tool

1 x 35-2151 1/8” NPT Female Hose Adapter

1 x 35-2149 Boost Tee

1 x 8-161 36” Vacuum Hose

4 x 1-117 Zip Tie

CAUTION:

When working with the fuel system, choose a suitable

work area that is well ventilated and free from any

sparks or open flames. Do not smoke while working

on the fuel system. Most fuel systems remain

pressurized for a period of time, after the key has been

turned off. Be sure to relieve the pressure before

installing the sensor. This can often be accomplished

by removing the fuel pump fuse and cranking/running

the engine.

1 2 3 4 5 6 7

CAUTION: 1
INSTALLATION 2

Shrnutí obsahu

Strany 1 - CAUTION:

AEM Performance Electronics 2205 126th Street Unit A, Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310) 484-0152 http://www.aemelectronics.com

Strany 2 - INSTALLATION

Page 2 INSTALLATION 1. Disconnect the negative battery cable. 2. Secure the gauge in a 2 1/16th” (52MM) mounting hole with the supplied bracket. 3.

Strany 3

Page 3 BROWN – The BROWN wire should be connected to the Analog – input. If the EMS or similar device does not have a – input, the BROWN wire shoul

Strany 4

Page 4 Status Lights The AEM Pressure gauge has two status lights, see Figure 4. The status light on the left will flash if an out of range low v

Strany 5

Page 5 Analog Output The analog output from the AEM 100 PSI Pressure gauge is a linear dc voltage signal that varies from 0.5 Vdc at 0 psig (0 Bar) t

Strany 6

Page 6 3-pin sensor harness Red - 5V sensor power Black - Sensor ground Green - Sensor signal 8-pin power harness Red – 12V Power Black – Power groun

Strany 7

Page 7 12 MONTH LIMITED WARRANTY Advanced Engine Management Inc. warrants to the consumer that all AEM High Performance products will be free from de

Komentáře k této Příručce

Žádné komentáře

Aem 30-5144 Analog Boost Fuel Pressure SAE Gauge Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Pro auto Aem 30-5144 Analog Boost Fuel Pressure SAE Gauge. AEM 30-5144 Analog Boost Fuel Pressure SAE Gauge User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Pro auto Aem 30-5144 Analog Boost Fuel Pressure SAE Gauge