Aem 30-6053 Series 2 Plug & Play EMS Uživatelský manuál

Page 1 of 21 Installation Instructions for: EMS P/N 30-6053 Fits vehicles: 2006-2008 Honda S2000 AP2 F22C1 WARNING: ,! This installation is not f

Page 10 of 21 h) NOTE: the throttle range on this vehicle is set differently from other EMS applications! Disconnect the DBW connector on the throttl

Page 11 of 21 c) Note: This calibration needs to be properly tuned before driving the vehicle. It is intended for racing vehicles and may not operate

Page 12 of 21 Original Honda S2000 ECU Pinout This pinout is for the original wiring harness on the Honda S2000 showing the corresponding pin on the A

Page 13 of 21 Pin Name AEM EMS pin location Tapped or intercepted?B1 -- (HS 4 on EMS) D4 intercepted B2 Injector 4 (Injector 4 on EMS) B5 interc

Page 14 of 21 Pin Name AEM EMS pin location Tapped or intercepted?E1 Engine Coolant Temperature sensor 2 -- -- E2 -- -- -- E3 Logic Ground 3 --

Page 15 of 21 Application Notes for EMS P/N 30-6053 F22C1 Make: Acura/Honda Description Function Pin Model: S2000 Spare Injector Drivers: Injec

Page 16 of 21 Connection Diagram for EMS P/N 30-6053 Please note that the following pinout is for the AEM EMS and not the original Honda S2000 wiring

Page 17 of 21 Connection Diagram for EMS P/N 30-6053 Pin AEM adapter harness pinout (gray connectors wired to vehicle wiring harness) AEM EMS 30-60

Page 18 of 21 Connection Diagram for EMS P/N 30-6053 Pin AEM adapter harness pinout (gray connectors wired to vehicle wiring harness) AEM EMS 30-60

Page 19 of 21 Connection Diagram for EMS P/N 30-6053 Pin AEM adapter harness pinout (gray connectors wired to vehicle wiring harness) AEM EMS 30-60

Page 2 of 21 Thank you for purchasing an AEM Engine Management System. The AEM Engine Management System (EMS) is the result of extensive development

Page 20 of 21 Connection Diagram for EMS P/N 30-6053 Pin AEM adapter harness pinout (gray connectors wired to vehicle wiring harness) AEM EMS 30-60

Page 21 of 21 AEM Electronics Warranty Advanced Engine Management Inc. warrants to the consumer that all AEM Electronics products will be free from

Page 3 of 21 Read and understand these instructions BEFORE attempting to install this product. • Sufficient battery voltage during cranking (starting

Page 4 of 21 sensitive, you can depin Pin A1 that goes into the stock ECU, but the malfunction code for this sensor will turn on. If this is done, the

Page 5 of 21 1) Install AEMTuner software onto your PC The latest version of the AEMTuner software can be downloaded from the AEMTuner section of th

Page 6 of 21 d) Remove the clip that is hidden underneath the rubber sealing trim next to the dashboard and the clip for the plastic cover over the s

Page 7 of 21 g) How to use provided wire taps: Run harness TPS wire through Place vehicle wire in tap Screw in tap onto vehicle wire Plac

Page 8 of 21 i) Connect provided adapter harness to factory wiring harness and stock ECU. Then route the harness from the stock ECU through the driv

Page 9 of 21 2) Repin ECU pins (only necessary if adding or relocating ECU pins) a) Locate a small screwdriver (a precision 1.5mm wide flathead screw